This Is How You Make Your Own Flamethrower!

This particular flame thrower is made to fit in a normal backpack, keeping your arms and hands free for throwing flames while using it!

With an air compressor, a diesel nozzle, a fuel tank, some hose, and some fittings, you’ll have a flame thrower capable of running off of tiki torch fuel.

Here we have the step by step instructions, but you can find the full video instructions at the bottom of this post.

Step One:

Start with an air compressor. You’ll want to remove the regulator, and fill in the space left behind with a brass plug.

 

 

Step Two:

Tap a hole in the bottom of the compressor to add fittings.

 

Step Three:

Your fittings should look like this with the correct valves.

 

 

Step Four:

Run a host from the valve and fit the end with an internal check valve.

 

 

Step Five:

Connect the internal check valve to a diesel nozzle.

 

 

Step Six:

Remove the spout and add a pipe running down to a tip and hose as pictured. The tip and hose will run the fuel for your flame.

 

 

Step Seven:

Run a hose with a nozzle to a fuel tank tapped with a valve and fitting like this. Fill up your tank with tiki torch fuel. Add valve along the hose to better regulate your fuel.

 

Step Eight:

Spark up and start throwing flames! You can adjust with the nozzles on the hose. The whole rigging will fit neatly into a backpack.

Learn How To Make Your Own Propane Torch!

If there’s one word that can describe us as DIY-ers, it’s “resourceful.”

It’s almost like our minds just work a little different from everyone else’s. We’re constantly looking for ways to make use of everyday items, to work with our hands and build something useful.

Today, I have stumbled across this cool video on how to make your own propane torch. Check it out!

DIY Air Conditioner (Very Easy To Make!)

With spring here and summer just around the corner, its time to start preparing for high temperatures.

Heat waves cause serious illness and kill people in cities every summer.

Whether the cause is power outages or lack of access to air conditioning, people fall victim to the heat.

Even in less dire circumstances, being stuck without air conditioning in the summer can be extremely uncomfortable.

With the know how provided by this DIY, you can find quick relief and ensure your safety from dangerous heat waves.

 

Supplies:

Large Ice Chest

Ice

Water hose and access to running water

2 lengths of 1/4 inch vinyl tubing

1 length of 1/4 inch copper tubing

2 hose clamps

Box fan

 

Step 1.

Fill up your biggest and most insulated ice chest/cooler with ice and water. Either place it in a high place or stack up some crates, boxes, to create a sturdy platform for you cooler to sit on. When you’re all set up, run a water hose into the cooler and leave it running.

 

 

Step 2.

Connect a length of 1/4 inch vinyl tubing and 1/4 inch copper tubing with a hose clamp. Submerge the vinyl end of the tubing into your filled ice chest, weighing it down under the water with a small weight tied around the tube.

 

 

Step 3.

Connect your copper tubing along one end of a box fan, running side to side along the face of the fan leaving a little space between the rows of tube. Fix into place with zip ties. This will create your “radiator”.

 

 

Step 4.

Warm air enters the fan, passing over your copper tubing full of ice cold water, causing the air to cool before continuing through the fan onto the other side.

 

 

Step 5.

Cool air pumps out of the fan, creating air conditioning.

 

 

Step 6.

Take the end of your copper tubing and run it out and away from your fan, then add another length of vinyl tubing with a hose clamp. This will be your outflow. Either run it outdoors, somewhere with a sink, or somewhere you can use the water…

 

 

Extra Tip:

This whole operation relies on gravity! That’s why your cooler is propped up  somewhere high. Therefore, your outflow must remain lower than your cooler at all times. Once you’re all set up, create suction on your outflow to get the cold air pumping and the air conditioner working.

 

Make Your Own Antiseptic Ointment

For treating minor cuts, scrapes, abrasions etc, most people will reach for the Neosporin or some other antiseptic ointments.

These are great items to keep in your first aid kit, but hold on just a second before you rush out the the pharmacy to stock up on these…

Did you know that instead of wasting $5 to $10 on ointment, you can make your own antiseptic from scratch?

This homemade antiseptic ointment is packed with germ-killing properties that will help treat those everyday minor cuts, scrapes, and abrasions you might have, and best of all, it’s really easy to make.

Supplies:

            • 1 1/2 ounces beeswax, grated
            • 1 cup olive, almond, or coconut oil
            • 1/4 teaspoon vitamin E oil
            • 1/2 teaspoon tea tree oil
            • 20 drops lavender essential oil
            • 10 drops lemon essential oil

Ointment Recipe Directions:

1. In a small pot, and melt the oils (except the lavender and lemon essential oils) and beeswax using low heat.

2. Remove pot from the heat and add Vitamin E oil, lemon, and lavender essential oil. Stir with a chopstick or a small wooden spoon.

3. Pour the mixture into a small sterilized jar (or a mason jar). Then let stand and cool on the counter.

4. Store it in a dark cool place.

When you get a cut, scrape or abrasion, use this ointment as needed on the wound.

It should keep for roughly 5 years.

How does it work?

The antiseptic properties include:

        • Tea tree oil: antibiotic, anti-fungal, antiviral, antibacterial
        • Lavender: analgesic (pain relief), antibiotic, anti-fungal, antiviral, and antibacterial
        • Lemon: antibiotic, antifungal, antiviral, antibacterial

DIY Powerful Slingshot

Have you ever wanted to make your own powerful slingshot?

Today’s tutorial will show you how.

Check out the DIY slingshot tutorial below.

INSTRUCTIONS

1. Start off with a half inch PVC tubing and some sprinkler fittings.

2. Once you attach all the pieces, the frame of your slingshot should look something like this.

3. Put the pieces together.

4. Use spray paint or duct tape to give your slingshot a custom look.

5. Use an exercise band to create the sling.

6. Make a launching pouch using duct tape.

7. Your finished product will look something like this.

For the full tutorial check out the video here.

DIY Citrus Cleaner

Homemade cleaners are the best right now, and it’s easy to see why…

People are tired of paying big bucks for store-bought cleaners than almost require a gas mask in order to use safely. Plus, many homemade versions work just as good, if not better than the commercial brands. So what’s not to love?

 I’ve used a 50/50 mix of white vinegar and water as an all-purpose cleaner for years now… But, not gonna lie, sometimes I miss the fancy “flavors” and scents of the store-bought cleaners.

Which is why I’ve been thrilled to find a new “recipe” for my all-purpose cleaner.

Plus, it’s a great way to use up those citrus peels that I always seem to accumulate. My goats and chickens generally don’t care for them, and you can only put so many down the garbage disposal!

DIY ALL-PURPOSE CITRUS CLEANER

You will need:

  • 1 or 2 quart sized mason jars
  • A spray bottle (a repurposed one is just fine!)
  • White vinegar (around 1-2 quarts)
  • Orange, grapefruit, lemon, or lime peels (any combination of these will work, too)
  • 3 -4 drops of lemon, grapefruit, or orange essential oil (optional)

Fill your quart jars about half full of citrus peels. Feel free to pack them in there if you need to. I used a combo of orange and grapefruit peels for this batch.

Fill the jars the rest of the way up with white vinegar. Cover tightly with a lid, give it a good shake, and then write the date on the top so you don’t forget!

 

Allow the peels and vinegar to steep for 2-3 weeks.

After time has elapsed, remove the peels from the mixture and strain through a fine strainer to remove any bits of citrus that might be floating in your vinegar. Dilute 1:1 with water (one part citrus vinegar to one part water) and place in a spray bottle.

You may add 3-4 drops of your choice of essential oil if you wish at this point. It’s not absolutely necessary, but I like the extra citrusy-boost that the oils give the mixture, plus they also boost it’s cleaning power.

Use as you would your plain vinegar cleaner: on sinks, countertops, bathtubs, toilets, floors, etc!

It’s amazing how the little changes can make your daily tasks just a bit more fun. I won’t go as far to say that I like cleaning the bathroom now, but it is just a little more pleasant than it was before.